Does A Suzuki Swift Have A Timing Belt (Cambelt) Or A Chain?
- The timing chain and water pump are both labor-intensive jobs in the same area of the engine, so knocking out both now can prevent having to do many of the same steps again later. Disconnect battery, chock the wheels, and set the parking brake.
- Replace the cylinder head if necessary. Follow specific procedures to time LF 2.0L and L3/L3T 2.3L engines. Timing the LF / 2.0L engine, the L3 and L3T / 2.3L engines must be done following specific procedures. This Job Aid explains how to verify base engine timing (relation of intake camshaft, exhaust camshaft.
- Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356 STEP 10: in onto the crankshaft sprocket, aligning the copper (marked) link with the timing marks on the sprock STEP 11: dowel pin and install the LH timing chain tensioner. NOTE: The LH owel hole for identification. Ngines with non-ratcheting timing chain tensioners.
Here is a list of timing belts and timing chains for a Suzuki Swift. Reference the model year with the corresponding engine to see if your car has a belt or a chain.
OE Solutions™ Plastic Timing Chain Cover by Dorman®. This premium product is the best way to go for those looking for the highest quality replacement that offers supreme levels of quality, performance and reliability. Oil Pump Chain Module Overview Replace item #1 in the illustration. Item #1 Chain Drive includes the gears, chain and tensioning device. The bolts are reusable as per the applicable repair instructions. Timing Chain Module Overview Replace the following components in the illustration. #1 –Timing chain #2 –Chain tensioner and guide rail #3.
Suzuki Swift | ||
---|---|---|
Model Year | Engine | Belt / Chain |
1988 - 2003 | 1.0 L G10 I3 | timing belt |
1.0 L G10T turbo I3 | timing belt | |
1.3 L G13A/BA I4 | timing belt | |
1.3 L G13B/G13K DOHC I4 | timing belt | |
1.5 L G15A I4 | timing belt | |
1.6 L G16 I4 | timing belt | |
2004 - 2010 | 1.2 L k-series I4 (petrol) | timing chain |
1.3 L M13A I4 (petrol) | timing chain | |
1.5 L M15A I4 (petrol) | timing chain | |
1.6 L M16A I4 (petrol) | timing chain | |
1.3 L DDis I4 (diesel) | timing chain | |
2010 - 2017 | 1.2 L K12B I4 (petrol) | timing chain |
1.4 L K14B I4 (petrol) | timing chain | |
1.6 L M16A I4 (petrol) | timing chain | |
1.3 Fiat Multijet | timing chain |
Which models have a belt/chain?
1988 - 2003:
From 1988 to 2003 Suzuki Swift cars with the G10, G13A, G13B, G15A and G16 engines have a timing belt.2004 - 2017:
From 2004 to 2017 Swift cars with the k-series, M13A, M15A, M16A and fiat engines have a timing chain.Suzuki Swift
TIMING CHAIN REMOVAL/INSTALLATION
Warning
- Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.
- Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injures or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete the Fuel Line Safety Procedure. (See Fuel Line Safety Procedure.)
1. Disconnect the negative battery cable.
2. Remove the spark plugs. (See SPARK PLUG REMOVAL/INSTALLATION.)
3. Remove the tire (RH).
4. Remove the under cover.
5. Loosen the water pump pulley bolt and removal the drive belt. (See DRIVE BELT REPLACEMENT.)
6. Remove the CKP sensor. (See CRANKSHAFT POSITION (CKP) SENSOR REMOVAL/INSTALLATION.)
7. Drain the engine oil. (See ENGINE OIL REPLACEMENT.)
8. Remove the P/S oil pump with the oil hose still connected and position the P/S oil pump so that it is out of the way. (See POWER STEERING OIL PUMP REMOVAL/INSTALLATION.)
9. Remove the front drive shaft (RH) from the joint shaft. (See JOINT SHAFT REMOVAL/INSTALLATION.)
10. Remove in the order indicated in the table.
11. Install in the reverse order of removal.
12. Start the engine and:
- Inspect for the engine oil, engine coolant, transaxle oil and fuel leakage.
- Verify the ignition timing, idle speed and idle mixture. (See IGNITION TIMING INSPECTION.) (See IDLE MIXTURE INSPECTION.)
13. Perform a road test.
Crankshaft Pulley Lock Bolt Removal Note
1. Remove the cylinder block lower blind plug.
2. Install the SST
.
3. Turn the crankshaft clockwise the crankshaft is in the No.1 cylinder TDC position.
4. Hold the crankshaft pully by using the SSTs
.
Chain Tensioner Removal Note
1. Using a thin screwdriver, hold the chain tensioner ratchet lock mechanism away from the ratchet stem.
2. Slowly compress the tensioner piston.
3. Hold the tensioner piston using a 1.5 mm {0.059 in}
wire or paper clip.
No.3 Engine Mount Rubber and No.3 Engine Joint Bracket Removal Note
Suspend the engine using the SSTs
.
Oil Pump Sprocket Removal Note
Hold the oil pump sprocket by using the SST
.
Engine Front Cover Removal Note
Remove the oil seal using a screwdriver as shown.
Oil Pump Sprocket Installation Note
Hold the oil pump sprocket by using the SST
.
Timing Chain Installation Note
Install the SST
to the camshaft as shown. Arturia jupiter 8v v3 3 1 crack mac free download.
European countries
Except European countries
2. Install the timing chain.
3. Remove the retaining wire or paper clip from the auto tensioner to apply tension to the timing chain.
Engine Front Cover Installation Note
1. Apply silicone sealant to the engine front cover as shown.
Caution
- Install the cylinder head cover within 10 minutes of applying the silicone sealant.
- Silicone sealant is not need in area C as indicated below due to an existing. (L3)
Thickness
A: 2.0-3.0 mm {0.079-0.118 in} B: 1.5-2.5 mm {0.059-0.098 in}
A: 2.0-3.0 mm {0.079-0.118 in} B: 1.5-2.5 mm {0.059-0.098 in}
2. Install the cylinder head cover bolts in the order as shown.
Front Oil Seal Installation Note
1. Apply clean engine oil to the oil seal.
2. Push the oil seal slightly in by hand.
3. Compress the oil seal using the SST
and a hammer.
No.3 Engine Mount Rubber and No.3 Engine Joint Bracket Installation Note
1. Tighten the stud bolt of the No.3 engine mount bracket.
Tightening torque: 7.0-13 N·m {71.4-132.5 kgf·cm, 62.0-115.0 in·lbf}
2. Install the No.3 engine mount rubber hand-tighten.
3. Tighten the No.3 engine joint bracket is attached and bolts, nuts in the order shown.
Timing Chain Kit
Crankshaft Pulley Lock Bolt Installation Note
1. Install the SST
to the camshaft as shown.
European countries
Except European countries
2. Install the M6 x 1.0 bolt
in by hand.
3. Turn the crankshaft clockwise the crankshaft is in the No.1 cylinder TDC position.
4. Hold the crankshaft pully by using the SST
.
5. Tighten the crankshaft pulley lock bolt using the following two steps.
(1) Tighten to 96-104 N·m {9.8-10.6 kgf·m, 70.9-76.7 ft·lbf}
(2) Tighten 87°-93°
6. Remove the M6 x 1.0 bolt.
7. Remove the SST
from the camshaft.
8. Remove the SST
from the cylinder block lower blind plug.
Chain Replacement Timing Belt
9. Rotate the crankshaft clockwise two turns until the TDC position.
- If not aligned, loosen the crankshaft pulley lock bolt and repeat from Step 1.
10. Install the cylinder block lower blind plug.
Tightening torque: 18-22 N·m {1.9-2.2 kgf·m, 13.3-16.2 ft·lbf}
Cylinder Head Cover Installation Note
1. Apply silicone sealant to the mating faces as shown.
Caution
- Install the cylinder head cover within 10 minutes of applying the silicone sealant.
Dot diameter:
4.0-6.0 mm {0.16-0.23 in}
4.0-6.0 mm {0.16-0.23 in}
2. Install the cylinder head cover with a new gasket.
3. Tighten the bolts in the order shown.
Timing Chain Vs Belt
Tightening torque: 8.0-11.5 N·m {81.6-122.3 kgf·cm, 70.9-106.2 in·lbf}
Compression pressure
COMPRESSION INSPECTION Warning Hot engines and oil can cause severe burns. Be careful not to burn yourself during removal/installation of each component. 1. Verify that the battery is fully ..Cylinder head gasket
CYLINDER HEAD GASKET REPLACEMENT Warning Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel. Fuel line spills ..Other materials:
Mazda 6 Service Manual: Air bag module and pre-tensioner seat belt deployment procedures
Warning A live (undeployed) air bag module and pre-tensioner seat belt may accidentally deploy when it is disposed of and cause serious injury. Do not dispose of a live (undeployed) air bag module and pre-tensioner seat belt. If the SSTs (Deployment tool and Adapter harness) are not ava ..
Warning A live (undeployed) air bag module and pre-tensioner seat belt may accidentally deploy when it is disposed of and cause serious injury. Do not dispose of a live (undeployed) air bag module and pre-tensioner seat belt. If the SSTs (Deployment tool and Adapter harness) are not ava ..
Swift Timing Chain Replacement Manual Download
Mazda 6 Service Manual: Oil seal replacement
1. Drain the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT.) Caution The oil seal is easily damaged by the sharp edges of the drive shaft splines. Do not let the splines contact the oil seal. 2. Remove the drive shaft. (See DRIVE SHAFT REMOVAL/INSTALLATION.) 3. Remove the oil sea ..
1. Drain the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT.) Caution The oil seal is easily damaged by the sharp edges of the drive shaft splines. Do not let the splines contact the oil seal. 2. Remove the drive shaft. (See DRIVE SHAFT REMOVAL/INSTALLATION.) 3. Remove the oil sea ..